5 Amazing Tips to Fix a Broken Bong

 

We can fully empathize with you. You must be inconsolable with the pain and depression which is shattering you from the inside. Have you just dropped your bong or bumped it against a piece of furniture? After breaking into pieces, it must have broken your heart. If you’re contemplating buying another one from any of the leading bong distributors in Ontario, then you shouldn’t bother as we won't allow this incident to be the end of your love story.  

 

In this write-up, we will guide you on how conveniently and quickly you can repair your bong. So, let's begin! 

 
At the very outset, if you can make a fair estimate about the extent of the damage, then you must realize that all bongs can’t be repaired. These methods may be applicable for glass pieces whose condition is within the scope of any repair. You may assess the condition of your bong by comparing the damage with the following: 

 

• When the bong is broken into ten or more pieces, then it’s a waste of your time trying the repair.  

• When the hole in the bong is bigger than the size of a pea, then it can't be fixed 

 

However, most smoking accessories distributors in Ontario believe that minor cracks, chips, and clean breaks can be repaired effortlessly, and a broken glass bong can be restored with a bit of glue and some prep work. 

 

1. Two-Part Epoxy 

 

The 'two-part' as the name suggests is that this epoxy is a polymerized blend of two substances, hardener, and resin. The detailed formatting may suggest that there would be limited availability of this substance. However, that is not so. Several brands offer heat and water-resistant substances to glue glass. Moreover, you can effortlessly get this long-lasting solution to keep the glass pieces attached. 

 
But a flaw is that it can get waterlogged faster. Once you submerge this seal in water for a very long time, the seal will become useless and may peel off. The easiest solution is to keep the bong emptied between the users. 

 
This epoxy can exclusively work on clean cuts. That’s why, even if the broken glass surface is bumpy or sharp, you may need to buy a glass cutter and maintain the smoothness of the broken area and evenly cut. Smooth out the sharp edges with sandpaper before using epoxy. 

 

2. Food Grade Silicone 

 

What could be better than using a waterproof and non-toxic material to repair your bong? The food-grade sealant is a convenient and reliable way to fix your broken bong. Although if the structure of your bong is ruined, it cannot be repaired using this method. 

 
Once ready, apply the food-grade Silicone to the affected area, cracks, and any pieces that are chipped off and the bong will be good as new. If the patch doesn't work, you can easily remove it by peeling it off and experimenting with another method. This method is to use and leave no mess. But make sure to apply the silicone to the joints of the bong or where the tube connects with the base. 

 
Keep in mind that you can't just cover the entire bong with food-grade silicone and expect it to work correctly. While using waterproof glue is preferred, you can also use non-waterproof glue. Simply apply the glue and then cover the glue with silicone and water will be ineffective in that area. 

 

3. JB Weld, Quick Steel, Plumber's Putty 

 

These sealants have putty-like evenness that can conveniently be shaped into cracks. 
Three putties are waterproof; JB Weld and Quick Steel are identical products and will become stuffy and unbendable after curing. However, the plumber’s putty won’t dry up and will stay moldable long after its application. But you should never use these in any areas that may become hot due to toxic chemicals. 

 

4. Loctite Glass 

 

The utility and look of this adhesive are almost the same as super-glue. However, the chemical constitutions of the two are quite dissimilar. This adhesive is a butyl formula that is very effective to bond shattered pieces of glass together. This procedure should be your top priority whenever you have to repair your bong. Don’t worry about unreasonable heat and water impacting the usefulness of the glue and making it repetitious. 

 
Nevertheless, you may not choose it as a long-term solution as it contains a few harmful chemicals for your health if consumed. It is better to seal small cracks and glue bowl pieces, however, it necessitates regular changes.   

 

5. Blow Torch 

 

Employing a torch shouldn’t be a part of any DIY project. That’s why you must ensure that you adopt all safety precautions if you try. It is better to leave this challenging task for the professionals. The maximum materials from which a bong is made normally melt at very high temperatures. This may mandate a propane or butane blow torch. Glass alone begins melting at 560 degrees. 

 
Your ideal possibilities are to grab an acetylene torch and a kiln to liquefy glass at such a high temperature. However, this must be the option you attempt least as it demands skill and due diligence. This is the only method to instruct you to super-heat the bong and fully dissolve the glass so that it communes.  

 

Inference 

 

If you want the most authentic quality of bongs, then you should exclusively visit the best bong shop in Ontario. They’ll guide you about maintaining the bongs in such a way that they don’t break easily.